FORTISVEX California State Flag 4x6 Feet Polyester - Made in USA Bear Flag with Brass Grommets

An open lot with an in-ground flagpole is where the polyester 4x6 foot flag belongs, since nylon looks great there but fails fast. The trade is straightforward: heavier, longer-lasting.

This is the California state flag at 4x6 Feet (24 square feet) in polyester, made in the United States and finished with brass grommets.

Built to the California flag specification

The California flag is set out in California Government Code Section 420, one of the most precise flag statutes in the country. It is two thirds as tall as it is long, with a red stripe along the bottom exactly one sixth of the height, a grizzly bear walking left across a green grass plot of twelve tufts and measuring two thirds of the flag’s height from nose to hind paw, one red five-pointed star in the upper hoist corner, and the words California Republic in condensed gothic capitals between the grass and the stripe.

Adopted in 1911 and standardized to its current form in 1953; it derives from the original Bear Flag raised at Sonoma during the Bear Flag Revolt of 1846, when a short-lived republic declared independence from Mexico and lasted twenty five days; the design is credited to William Todd, a nephew of Mary Todd Lincoln, who painted the original at Sonoma.

California is precise about proportion. Government Code Section 420 makes the flag two thirds as tall as it is long, which is two to three, and a 4x6 foot flag, an 8x12 foot flag, a 10x15 foot flag and a 12x18 foot flag all match it exactly. A 3x5 foot flag is a three to five ratio and is therefore slightly deeper than the statute describes, which is true of almost every 3x5 foot state flag sold in the country.

Faithfully reproduced, that is the standard we hold this design to, at the outdoor sizes the whole industry uses and states themselves order. What an outdoor flag needs right is the color, the seal and the emblems, and this one has them right.

The law that defines it, in its own words

California Government Code Section 420 reads:

The Bear Flag is the State Flag of California. As viewed with the hoist end of the flag to the left of the observer there appears in the upper left-hand corner of a white field a five-pointed red star with one point vertically upward and in the middle of the white field a brown grizzly bear walking toward the left with all four paws on a green grass plot, with head and eye turned slightly toward the observer; a red stripe forms the length of the flag at the bottom, and between the grass plot and the red stripe appear the words CALIFORNIA REPUBLIC. Dimensions, excluding heading and unfinished flag ends: The hoist or flag width is two-thirds of the fly or flag length; the red stripe width is one-sixth of the hoist width. The state official flag hoist widths shall be two, three, four, five, six and eight feet.

The section continues with the proportions of the star, bear, grass plot and lettering, then the Textile Color Card Association references: White cable 70001, Old Glory red 70180, Irish Green 70168, Maple Sugar brown 70129, Seal dark brown 70108. The bear illustration itself appears only in the printed Statutes of 1953, chapter 1140.

You do not have to take our word for any of that. Read California Government Code Section 420 in full at Justia, and check what we sell against it.

That is the flag we build, not a rough version of it.

What is on it and what it means

The bear is a California grizzly, a subspecies now extinct. The last one held in captivity, a bear named Monarch, was the model used when the flag was standardized. The star recalls the lone star of the 1836 California revolt. The original 1846 flag was destroyed in the San Francisco fire of 1906.

What most listings get wrong

Three errors are repeated constantly by other retailers and by general reference sites. The bear walks on all fours; it does not stand upright. The words California Republic sit below the bear, not above it. And the word Eureka belongs to the state seal, not to the flag, so any California flag carrying it is wrong.

Where the California flag flies

The Superflag, five hundred and five by two hundred and twenty five feet and about three thousand pounds, was made for Thomas Demski of Long Beach and was recognized by Guinness as the world's largest flag in the 1994 and 1995 editions. Its 1996 unfurling at Hoover Dam made it the largest flag flown. It no longer holds the world title but is still cited as the largest American flag. Calipatria in Imperial County has a one hundred and eighty four foot municipal flagpole so the flag flies at sea level in a town one hundred and eighty four feet below it. Dorris is documented as having one of the tallest United States flagpoles.

Fly it on California’s birthday

California became the 31st state on September 9, 1850. Under the United States Flag Code as amended July 7, 1976, a state flag flown on the state’s birthday takes its place beneath the United States flag, and that day is the one date every year the California flag has an official reason to go up.

California Admission Day is September 9, a legal observance, and some cities close offices for it.

Buy it now and it is on the flagpole for the day. The full list of state birthdays is on our state birthdays page.

Nylon or polyester in California

Nylon in the mild sheltered coastal valley metros, the Los Angeles basin, San Diego, San Jose and Sacramento. Polyester on the immediate coast for salt, in the high wind passes at San Gorgonio and Altamont, and in the high ultraviolet desert at Palm Springs and the Bakersfield edge.

For scale, the National Weather Service ultraviolet index forecast for Los Angeles on July 23, 2026 was 11 at solar noon, in the extreme band. That is the sun this flag has to survive.

At twenty four square feet the wind load starts to matter, and the verdict above applies with more force than it does to a house flag.

Here is the two-ply polyester, right for the exposed, windy, coastal and high sun sites listed above, and for any flagpole that runs around the clock. The fiber tells the story: polyester’s ester bonds stand up to ultraviolet where nylon’s amide bonds give out, so color and strength last longer in sun. Almost no water is absorbed, so wet or dry it is equally strong, salt sheds rather than sticking, and there is less to freeze in cold. The open weave lets fast wind through the fabric instead of loading it, and that is what lets it outlast nylon on an exposed pole. The trade is calm days — heavier, it hangs still on a quiet afternoon while nylon would still be moving. A sheltered site favors the nylon version instead.

One more thing that decides it, and it is the part people only learn after buying twice: replacing a flag twice a year on a tall flagpole is not just the price of the flag. It is the ladder, the halyard, the time, and on a commercial site somebody’s hour. The heavier material costs more once and saves that. On an exposed flagpole this is the cheaper flag over three years even though it is the dearer one today.

Most institutions work from the same benchmark, reported by the American Legion: the United States government's expectation is roughly ninety days for a flag flown daily sunrise to sunset, and about a quarter of that for one flown around the clock. In practice, retailers report three to six months for nylon flown daily, four to eight for polyester, and one to three years for a flag flown only on occasions. These are working numbers, not a guarantee, and exposure can move them substantially either way.

How the 4x6 Feet is built

The extra area on a 4x6 foot flag — more than half again a 3x5 Feet's — means more wind caught and a harder-working fly end. Four rows of lock stitching, all four earning their place.

Here is the arithmetic: 24 square feet of two-ply spun polyester at roughly four ounces a square yard. A thirty mile an hour wind sends the fly end moving faster than the wind itself, since the wave traveling toward the tip picks up speed as it goes — which is why the tip wears out first, and why the fly end's stitching count is the figure to check on any listing.

Still a one person job, but you will notice the difference the first windy day you try to take it down alone. Do it before the weather, not during it.

With lock stitching, every stitch knots into its neighbor, so damage stays contained at the break instead of running down the seam. Read 4 rows not as 4 times the strength but as 3 backups. Two solid brass grommets with tooth washers sit in a reinforced, inch and a half heavy duty white heading. Twenty four square feet puts genuine load on those two points.

This is two-ply spun polyester, the heavier of the two materials. Woven open so wind moves through rather than against it, it keeps its strength wet and holds color longer under strong sun. The trade off is straightforward: it weighs more, needs more wind to fly, and costs more.

Why this flag is harder to make than most

A detailed bear silhouette, a twelve-tuft grass plot, lettering and a star, and a statute that fixes proportions precisely enough that a sloppy reproduction is visibly wrong.

For what it is worth, the North American Vexillological Association surveyed 72 state, provincial and territorial flags in 2001 and rated them from zero to ten. The California flag placed 13, at 7.00 out of 10.

Will it fit my flagpole?

An in-ground flagpole between eighteen and twenty five feet is the right fit; a six foot house bracket will leave it dragging and wrapping.

Questions about the 4x6 Feet

What flagpole does a 4x6 foot flag need? An in-ground flagpole of eighteen to twenty five feet. It is too large for a standard house bracket, which is the honest reason to choose it.

Is a 4x6 foot flag worth it over a 3x5 foot flag? Only if the flagpole is tall enough. On a twenty foot flagpole a 3x5 foot flag looks lost and a 4x6 foot flag fills it. On a six foot bracket the 4x6 foot flag will wrap.

Can I fly a 4x6 foot state flag with a 4x6 foot United States flag? Yes, and on two flagpoles of equal height that is the correct pairing, with the United States flag to the viewer’s left.

The size where the flag material starts to decide

A 4x6 foot flag has half again the area of a 3x5 foot flag and catches proportionally more wind. This is the first size where the choice of flag material, nylon or polyester, changes how many flags you buy in a year.

Specifications

• Size: 4x6 Feet
• Area: 24 square feet
• Material: 100 percent two-ply spun polyester
• Fly end: 4 rows of lock stitching
• Heading: heavy duty white, reinforced, 1-1/2 inch
• Finish: Brass Grommets
• Ink: UV resistant, field tested
• Made in the United States by FORTISVEX

Which size do I need?

The rule that governs both tables is a length-to-height ratio of about one quarter to one third. Borderline cases favor the smaller size if you want it flying often and lasting, or the larger size if the point is to be seen from a distance.

If you know your flagpole height, start here.

• 6 Feet house bracket: 2x3 Feet or 3x5 Feet
• 15 to 20 Feet flagpole: 3x5 Feet or 4x6 Feet
• 20 to 25 Feet flagpole: 4x6 Feet or 5x8 Feet
• 25 to 35 Feet flagpole: 5x8 Feet or 6x10 Feet
• 35 to 45 Feet flagpole: 6x10 Feet or 8x12 Feet
• 45 to 60 Feet flagpole: 8x12 Feet or 10x15 Feet
• 60 to 80 Feet flagpole: 10x15 Feet or 12x18 Feet
• 80 to 100 Feet flagpole: 12x18 Feet or 15x25 Feet
• 100 to 120 Feet flagpole: 15x25 Feet or 20x30 Feet
• 120 to 150 Feet flagpole: 20x30 Feet or 20x38 Feet
• 150 to 200 Feet flagpole: 20x38 Feet or 30x50 Feet
• 200 to 240 Feet flagpole: 30x50 Feet or 30x60 Feet
• 240 Feet and above: 30x60 Feet or 50x80 Feet, engineered to the flagpole

If you know your flag size, start here.

• 2x3 Feet: 4 to 8 Feet bracket or garden flagpole
• 3x5 Feet: 6 Feet bracket, or 15 to 20 Feet in-ground flagpole
• 4x6 Feet: 18 to 25 Feet in-ground flagpole
• 5x8 Feet: 25 to 35 Feet flagpole
• 6x10 Feet: 30 to 40 Feet flagpole
• 8x12 Feet: 40 to 50 Feet flagpole
• 10x15 Feet: 50 to 60 Feet flagpole
• 12x18 Feet: 60 to 80 Feet flagpole
• 15x25 Feet: 80 to 100 Feet flagpole
• 20x30 Feet: 100 to 120 Feet flagpole
• 20x38 Feet: 120 to 150 Feet flagpole. This is the garrison size under Executive Order 10834, at a one to one point nine ratio rather than the two to three of the commercial sizes, and it is the size flown at the White House and the Capitol
• 30x50 Feet: 150 to 200 Feet flagpole
• 30x60 Feet: 200 to 240 Feet flagpole. This is the largest standard commercial size
• 50x80 Feet: 240 Feet and above, engineered to the flagpole

The quarter to a third rule holds all the way up, but above about a hundred feet the flag and the flagpole stop being two purchases and become one engineered system: the truck, the halyard, the foundation and the wind load all have to be specified together, and a flag bought without checking the flagpole rating damages the flagpole first. Several famous installations deliberately fly longer than the rule, which is a choice made with an engineer rather than from a chart.

We do not limit ourselves to what is listed on the site. The full range above is available to order, and an unlisted size can still be supplied.

About the back of the flag

The back of a printed flag shows the design reversed, not missing. That is true of almost every flag in the country, and it is normal rather than a flaw. Getting both sides to read correctly means sewing two flags together with a liner between them, which roughly doubles the cost and the weight. Single sided is standard practice, and the right choice unless a particular state’s law says otherwise.

Flying it with the United States flag

Section 7 of Title 4, the United States Flag Code, addresses this directly: the United States flag is never outranked in position, staying above every other flag and to the right at the same level, which reads as the viewer’s left. Same-height flagpoles put the United States flag on the viewer’s left with matching flag sizes; different heights put it on the taller pole; one flagpole with two flags puts it at the top. There is no legal penalty for civilians under the Flag Code, but it is what every institution follows anyway.

Buy two and they both last longer

Keep two flags and swap them monthly. That single habit will outlast three flags run to destruction, since resting fabric recovers and the fly end is spared the repeated wear of constant flying. Take the flag down ahead of severe weather, since one bad storm night can outdo six calm months. Watch the fly end rather than the center; a little stitching early saves a whole season.

For cities, counties, schools and agencies

Our state flags go to municipalities, school districts, fire and police departments, courthouses and state agencies regularly. Tax exempt purchasing is handled on the tax exempt page. For quantity, a replacement schedule, or a size outside this listing, use the contact page.

Why buy it from us

This is a small American company, and what you see listed is what we actually stock. Every flag is made in the United States, printed with UV resistant ink, and built to the construction described above, not to whatever a price point demands. Selling one flag that lasts beats selling three that fail. Orders over twenty five dollars ship free.